当前位置:首页-新闻动态 > 行业资讯 >

你知道彩钢板安装时需要注意哪些事项吗?

来源:http://www.jnqkgjg.com 日期:2019-01-09 发布人:admin

彩钢板的装置事项:

Installation of color steel plate:
榜首、起吊压型钢板时,用木板或柔软物垫在钢板与钢索之间,避免钢板刮伤或变形
When lifting profiled steel sheets, the top of the list should be placed between the steel sheets and the cables with wooden boards or soft objects to avoid scratches or deformation of the steel sheets.
第二、装置钢板前要先检查其外观质量,保证表面没有油污、泥沙、裂纹、剥落、擦痕等缺陷。
Secondly, before installing the steel plate, it is necessary to check its appearance quality to ensure that there are no oil, sediment, cracks, spalling, scratches and other defects on the surface.
第三、钢板铺设的板肋搭接缝应该与当地常年的风向相背。
Thirdly, the overlap joints of the plate and rib should be opposite to the local wind direction all the year round.
第四、基层钢板长向搭接长度为80—100mm,搭接处不需要上密封胶,从下面看压型钢板的接头处应该构成一条直线,并与檐口平行,接缝应均匀紧密。
Fourth, the overlap length of the base steel plate is 80-100 mm. There is no need for sealant at the overlap. From the bottom, the joint of profiled steel plate should form a straight line parallel to the eaves, and the joint should be uniform and close.
第五、上层压型钢板在屋脊的一端应该向上折弯80°角。上层压型钢板长向搭接长度应大于200mm,搭接处需上密封胶。从上面看压型钢板的接头处应该构成一条直线,并与檐口平行,接缝应均匀紧密。
Fifth, the upper profiled steel sheet should bend upward at an angle of 80 degrees at one end of the roof. The overlap length of the upper profiled steel sheet should be more than 200 mm, and sealant should be applied at the overlap. Seen from above, the joint of profiled steel sheet should form a straight line parallel to the eaves, and the joint should be uniform and close.
第六、泛水板、包角板的搭接长度应不小于100mm,搭接处需上密封胶。泛水板、包角板与压型钢板运用拉铆钉进行衔接,纵向和横向衔接的间距均不能大于1250px,应保证间距均匀,双面衔接处应对称,用密封胶封住铆钉处。
商河彩钢瓦
Sixth, the lap length of flooding plate and corner plate shall not be less than 100 mm, and sealant shall be applied at the lap. Flooding plate, angle cladding plate and profiled steel plate are joined by rivets. The spacing between longitudinal and transverse joints should not be greater than 1250 px. The spacing should be uniform, the joint of two sides should be symmetrical, and the rivet should be sealed with sealant.
第七、水槽、山墙泛水板与混凝土或砖女儿墙的结合处,应该用切割机将女儿墙切出深度大于10mm的缝缝隙,然后将泛水板的折边塞入缝隙中,刷上密封胶。运用水泥钉将泛水板固定于女儿墙上,用密封胶密封住水泥钉头。
Seventh, at the joints of water tank, wall panels and concrete or brick parapets, the parapets should be cut out with a cutting machine, and then the edges of the panels should be inserted into the cracks and sealed with sealant. The floodboard is fixed on the daughter's wall with cement nails, and the cement nail head is sealed with sealant.
第八、运用专用自攻枪打自攻钉,打每一排自攻钉均要带线,使一排自攻钉构成一条直线,并与屋脊或檐口平行,避免钻错孔,自攻钉应垂直于檩条和屋面板的衔接面。
Eighth, using special self-tapping gun to hit self-tapping nails, each row of self-tapping nails should be striped, so that a row of self-tapping nails form a straight line, parallel to the roof or eaves, to avoid drilling wrong holes, and the self-tapping nails should be perpendicular to the interface between purlin and roof panel.
第九、装置过程中要进行定段检测,检查钢板两头的平直度和平行度。
Ninth, in the process of installation, the flatness and parallelism of the two ends of the steel plate should be checked.
以上信息是我们商河彩钢瓦整理发布希望对大家有所帮助我们的网站是:http://www.jnqkgjg.com
The above information is our Shanghe color steel tiles collation and publication hope to help you with our website is: http://www.jnqkgjg.com!