当前位置:首页-新闻动态 > 行业资讯 >

你知道彩钢板该怎么吊装吗?

来源:http://www.jnqkgjg.com 日期:2018-12-25 发布人:admin

彩钢板的吊装
Lifting of coloured steel plate
夹芯板的吊装方法很多,如汽车吊吊升、塔吊吊升、卷扬机吊升和人工提升等方法。对 厂房檐高不大的单层轻钢厂房可采用人工提升的简便方法。 对办公楼檐高较大的建筑可采用卷扬机提升的方法, 由于不用大型机械, 设备可灵活移 动到需要安装的地点,故而方便而又价低。
There are many lifting methods for sandwich panel, such as automobile hoisting, tower hoisting, hoist hoisting and manual hoisting. Simple manual lifting method can be used for Single-storey light steel workshop with small eaves. Winch hoisting method can be used for buildings with large eaves of office buildings. Without large machinery, equipment can be flexibly moved to places where installation is needed, so it is convenient and cheap.
彩钢板的安装
Installation of coloured steel plate
1、实测安装板材的实际长度, 按实测长度核对对应板号的板材长度, 需要时对该板材进 行剪裁。
1. Measure the actual length of the installed plate, check the length of the corresponding plate number according to the measured length, and cut the plate when needed.
2、将提升到作业面的板材按排板起始线放置,并使板材的宽度覆盖标志线对准起始线。 并在板长方向两端排出设计的构造长度。
2. Place the plate raised to the working surface according to the starting line of the platen, and make the width of the plate cover the marking line to align with the starting line. The designed construction length is discharged at both ends of the plate length direction.
3、用紧固件紧固两端后,再安装第二块板,其安装顺序为先自左(右)至右(左),后自下 而上。
3. After fastening the two ends with fasteners, install the second plate. The installation sequence is from left (right) to right (left), then from bottom to top.
商河彩钢瓦
4、安装到放线标志点处, 复查板材安装的偏差, 当满足设计要求后进行板材的全面紧固。 不能满足要求时,应在下一标志段内调正,当在本标志段内可调正时,可调整本标志段后再 全面紧固。依次全面展开安装。
4. Install it at the marking point, check the deviation of plate installation, and tighten the plate completely after meeting the design requirements. If it fails to meet the requirements, it should be adjusted in the next marking section. When it can be adjusted in this marking section, the marking section can be adjusted and then fully tightened. Full installation is carried out in turn.
1)安装夹芯板时,应挤密板间缝隙,当就位准确,仍有缝隙时,应用密封胶填充。
1) When installing the sandwich board, the gap between the plates should be compacted. When the sealant is in place accurately and there are still gaps, it should be filled with sealant.
2)在紧固自攻螺丝时应掌握紧固的程度,不可过度。
2) When tightening self-tapping screw, we should grasp the degree of tightening, not excessive.
3)板的纵向搭接, 应按设计铺设密封条和设密封胶, 并在搭接处用自攻螺丝或带密封垫 的拉铆钉连接,紧固件应拉在密封条处。
3) Sealing strips and sealants should be laid according to the design for the longitudinal lapping of the plate, and self-tapping screw or rivet with sealing pad should be used to connect the lapping part. The fastener should be pulled at the sealing strip.
上述信息是由我们商河彩钢瓦整理发布希望大家能够喜欢我们的网站是:http://www.jnqkgjg.com
The above information is published by our Shanghe color steel tiles. I hope you will like our website: http://www.jnqkgjg.com!