当前位置:首页-新闻动态 > 公司动态 >

彩钢瓦安装的九大注意事项!

来源:http://www.jnqkgjg.com 日期:2019-01-08 发布人:admin

彩钢板在咱们的日常日子中很是常见,运用十分广泛,许多的范畴都有所触及,不过关于彩钢板的装置,许多人就不是很清楚了,今日小编来给我们介绍下。

Colored steel plate is very common in our daily life. It is widely used and touched in many fields. However, many people are not very clear about the installation of colored steel plate. Today Xiaobian will introduce it to us.
一、彩钢厂表示,起吊压型钢板时,要用木板或柔软物垫在钢板与钢索之间,避免钢板刮伤或变形。
First, the color steel plant said that when lifting profiled steel plate, it is necessary to use wooden board or soft mat between the steel plate and the steel cable to avoid scratch or deformation of the steel plate.
二、装置钢板前要先查看其外观质量,确保外表没有油污、泥沙、裂纹、剥落、擦痕等缺陷。
2. Before installing the steel plate, check its appearance quality to ensure that there are no defects such as oil, sediment, cracks, spalling, scratches and so on.
三、钢板铺设的板肋搭接缝应该与当地终年的风向相背。
3. The overlap joints of steel plates should be opposite to the local wind direction all the year round.
四、基层钢板长向搭接长度为80—100mm,搭接处不需要上密封胶,从下面看压型钢板的接头处应该构成一条直线,并与檐口平行,接缝应均匀紧密。
4. The overlap length of base steel plate is 80-100 mm in length. There is no need for sealant on the overlap. From the bottom, the joint of profiled steel plate should form a straight line parallel to the eaves, and the joint should be uniform and close.
五、上层压型钢板在屋脊的一端应该向上折弯80°角。上层压型钢板长向搭接长度应大于200mm,搭接处需上密封胶。从上面看压型钢板的接头处应该构成一条直线,并与檐口平行,接缝应均匀紧密。
5. The upper profiled steel sheet should bend upward at an angle of 80 degrees at one end of the roof. The overlap length of the upper profiled steel sheet should be more than 200 mm, and sealant should be applied at the overlap. Seen from above, the joint of profiled steel sheet should form a straight line parallel to the eaves, and the joint should be uniform and close.
六、彩钢厂指出,泛水板、包角板的搭接长度应不小于100mm,搭接处需上密封胶。泛水板、包角板与压型钢板运用拉铆钉进行衔接,纵向和横向衔接的间距均不能大于1250px,应确保间距均匀,双面衔接处应对称,用密封胶封住铆钉处。
商河彩钢瓦
6. The color steel plant pointed out that the lapping length of the flooding plate and the corner plate should not be less than 100 mm, and the lapping place should be covered with sealant. Flooding plate, angle cladding plate and profiled steel plate are joined by rivets. The spacing between longitudinal and transverse joints should not be greater than 1250px. The spacing should be uniform, the joint between two sides should be symmetrical, and the rivet should be sealed with sealant.
七、水槽、山墙泛水板与混凝土或砖女儿墙的结合处,应该用切割机将女儿墙切出深度大于10mm的缝缝隙,然后将泛水板的折边塞入缝隙中,刷上密封胶。运用水泥钉将泛水板固定于女儿墙上,用密封胶密封住水泥钉头。
Seventh, at the joint of the water tank, the floodboard of the gable and the concrete or brick parapet wall, the crack depth of the parapet wall is greater than 10 mm should be cut out by a cutting machine, and then the fold edge of the floodboard should be stuffed into the crack, and the sealant should be brushed. The floodboard is fixed on the daughter's wall with cement nails, and the cement nail head is sealed with sealant.
八、运用专用自攻枪打自攻钉,打每一排自攻钉均要带线,使一排自攻钉构成一条直线,并与屋脊或檐口平行,避免钻错孔,自攻钉应垂直于檩条和屋面板的衔接面。
8. Use special self-tapping gun to tap self-tapping nails. Each row of self-tapping nails should be striped so that a row of self-tapping nails can form a straight line parallel to the roof or eaves, so as to avoid drilling wrong holes. The self-tapping nails should be perpendicular to the interface between purlin and roof panel.
九、装置过程中要进行定段检测,查看钢板两端的平直度和平行度。
Ninth, in the process of installation, the flatness and parallelism of the two ends of the steel plate should be checked.
以上信息是我们商河彩钢瓦整理发布希望大家能够喜欢我们的网站是:http://www.jnqkgjg.com
The above information is our Shanghe color steel tile finishing and publishing hope that you can like our website is: http://www.jnqkgjg.com!